Tab Content
  • Rimmo's Avatar
    15-03-2019, 01:25 PM
    Rimmo replied to a thread Another 308 post in Holden V8's
    Here you go https://www.dura-bondbearing.com/wp-content/uploads/2018/06/Cam-bearing-oil-holeTechnical-Bulletin.pdf
    212 replies | 9055 view(s)
  • Rimmo's Avatar
    15-03-2019, 08:56 AM
    Rimmo replied to a thread Another 308 post in Holden V8's
    I didn't mean to put the wind up you Rielly. If you don't want to do any more block mods you can probably leave it as is. Some builders just clock...
    212 replies | 9055 view(s)
  • Rimmo's Avatar
    15-03-2019, 12:50 AM
    Rimmo replied to a thread Another 308 post in Holden V8's
    I've been trying to upload a pic of the extended groove in the front cam bore but it's too big to attach, but if you scroll down to post #12 in this...
    212 replies | 9055 view(s)
  • Rimmo's Avatar
    15-03-2019, 12:25 AM
    Rimmo replied to a thread Another 308 post in Holden V8's
    Here's a write up tk383 did on another forum about basic oil mods for 308's. You've already done a lot of this of this but worth a read. "Grind...
    212 replies | 9055 view(s)
  • Rimmo's Avatar
    15-03-2019, 12:19 AM
    Rimmo replied to a thread Another 308 post in Holden V8's
    Here's a couple of threads with the single pipe oil mod done for reference is you wan't to give it a go. ...
    212 replies | 9055 view(s)
  • Rimmo's Avatar
    14-03-2019, 03:32 PM
    Rimmo replied to a thread Another 308 post in Holden V8's
    If it was me I wouldn't worry about. I'd try it on the next build....and see the difference
    212 replies | 9055 view(s)
  • Rimmo's Avatar
    14-03-2019, 11:00 AM
    Rimmo replied to a thread Another 308 post in Holden V8's
    It costs nothing to do while you have the grinder out. I wouldn't worry too much if you haven't done it.
    212 replies | 9055 view(s)
  • Rimmo's Avatar
    13-03-2019, 08:09 PM
    Rimmo replied to a thread Another 308 post in Holden V8's
    You can grind the groove in No.1 cam bore round a bit further to allow you to clock the cam bearing feed hole @ 3 o'Álock when you install the...
    212 replies | 9055 view(s)
  • Rimmo's Avatar
    21-02-2019, 08:35 PM
    Rimmo replied to a thread 289 vs 302 in Ford V8's
    hmmmm...my hazy memory seems to recall the 289 block may have shorter bores, or was that the 260 block? OP may want to check some factory specs...
    20 replies | 1469 view(s)
  • Rimmo's Avatar
    20-02-2019, 10:36 PM
    Rimmo replied to a thread Another 308 post in Holden V8's
    A lot of the 350 chev pistons are only 1.54" comp height, just keep an eye on that. If you broaden your search I think some 4 cyl pontiac pistons...
    212 replies | 9055 view(s)
No More Results
About Rimmo

Basic Information

About Rimmo
Location:
Oz
Your Ride:
Always a V8

Statistics


Total Posts
Total Posts
519
Posts Per Day
0.11
General Information
Last Activity
15-03-2019 01:25 PM
Join Date
22-07-2006

1 Friend

  1. allports1 allports1 is offline

    Engine scientist

    allports1
Showing Friends 1 to 1 of 1