Tab Content
  • jezza355's Avatar
    03-01-2017, 07:50 PM
    jezza355 replied to a thread E85 in Holden V8's
    Too easy mate , I'll give it a whirl on e85 and see how it goes. Sent from my SM-G930F using Tapatalk
    37 replies | 2051 view(s)
  • jezza355's Avatar
    03-01-2017, 07:24 PM
    jezza355 replied to a thread E85 in Holden V8's
    In the process of changing it over at the moment , just in the middle of modifying an in tank e85 pump to fit in the cradle and changing hoses to...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    30-12-2016, 10:14 PM
    jezza355 replied to a thread E85 in Holden V8's
    So update on the pinging , gave it a clean out up top by hooking up an old water injection setup I have and drove around for half a tank , took it...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    29-12-2016, 08:03 PM
    jezza355 replied to a thread E85 in Holden V8's
    Grabbed some nulon pro strength today so I'll give it a run tomorrow night and see how it goes. Sent from my SM-G930F using Tapatalk
    37 replies | 2051 view(s)
  • jezza355's Avatar
    26-12-2016, 06:53 PM
    jezza355 replied to a thread E85 in Holden V8's
    All plugs are reading nice and clean , I'm leaning towards carbon hot spots in number one as that's the cylinder that had the injector stuck open. ...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    26-12-2016, 06:39 PM
    jezza355 replied to a thread E85 in Holden V8's
    Yeah cam dialled in at 0 , lift with 1.65 is 620 . I was given advice when buying bits and pieces for this engine that I could safely run 11.5 :1...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    26-12-2016, 09:50 AM
    jezza355 replied to a thread E85 in Holden V8's
    Yeah looking at the machine work invoice info they have 3cc valve reliefs , they were advertised at something different but when machine shop...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    26-12-2016, 12:49 AM
    jezza355 replied to a thread E85 in Holden V8's
    Yeah mate 355 , zero deck , 58cc chambers and 40 thou cometics Sent from my SM-G930F using Tapatalk
    37 replies | 2051 view(s)
  • jezza355's Avatar
    25-12-2016, 07:48 PM
    jezza355 replied to a thread E85 in Holden V8's
    Yeah mate , checked that when motor was being assembled was pretty well spot on. Sent from my SM-G930F using Tapatalk
    37 replies | 2051 view(s)
  • jezza355's Avatar
    25-12-2016, 04:47 PM
    jezza355 replied to a thread E85 in Holden V8's
    So took the car out for a run today, it's pretty warm here 35 degrees , slight ping at wot again with 24 degrees , dropped back to 22 and it stopped,...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    25-12-2016, 01:39 PM
    jezza355 replied to a thread E85 in Holden V8's
    I did have an injector stuck open for a bit while initially first tuning it , replaced that under warranty and sorted that . I'm wondering if I may...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    25-12-2016, 01:36 PM
    jezza355 replied to a thread E85 in Holden V8's
    Injected mate , afr is 12.5 at wide open from start to finish no lean spots . Tried all the way down to 12 flat and Still had some knock at 25...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    25-12-2016, 10:29 AM
    jezza355 replied to a thread E85 in Holden V8's
    What ignition setup are you running mate ? Sent from my SM-G930F using Tapatalk
    37 replies | 2051 view(s)
  • jezza355's Avatar
    24-12-2016, 08:40 PM
    jezza355 replied to a thread E85 in Holden V8's
    Cam is hydraulic roller 242/252 @50 on 108 centre . It made 380hp at the wheels but was limited to the 24 degrees timing . Afr,s at wot were 12.5 and...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    24-12-2016, 07:17 PM
    jezza355 replied to a thread E85 in Holden V8's
    It's running 11.5:1 and am having a few some detonation issues , can't seem to get much more than 24 degrees into it before it pings at wot , the 24...
    37 replies | 2051 view(s)
  • jezza355's Avatar
    24-12-2016, 04:16 PM
    jezza355 started a thread E85 in Holden V8's
    Has anyone converted a vn-vs v8 to e85 ? Just wondering if anyone who has had troubles with tank , steel lines etc with corrosion or any other issues...
    37 replies | 2051 view(s)
No More Results
About jezza355

Basic Information

About jezza355
Location:
Adelaide S.A.
Occupation:
Grease monkey
Your Ride:
VR ss , Wh stato

Statistics


Total Posts
Total Posts
80
Posts Per Day
0.03
General Information
Last Activity
Yesterday 03:15 PM
Join Date
28-04-2010