Page 6 of 9 FirstFirst ... 3456789 LastLast
Results 76 to 90 of 133
  1. #76
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default

    Not yet buddy Iíll take some photos when I get it back from the upholsterer

    Kinder what I was thinking, always worried lifting a cast iron motor with the plate so I never done it, I have seen a plate that bolts to the valley for LS

    For $150 I couldnít go wrong with the pipes

  2. #77
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default



    Tank nearly ready just need to remeasure for mounts

  3. #78
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default

    Tank fits in easy and buy the measurements should hold nearly 75ltrs,

    new engine mounts turned up today to push the motor back of course 1 of the bolts on the old mounts is a nightmare to get at so Iíll bend up a spanner to get onto it

    Iíll have a spare set of engine mounts to suit Ls1 in hq/wb using original cross member for the 4l60

  4. #79
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default

    New Engine mounts are in and line up perfect pipes have heaps of room around them, need to lift motor slightly as sump just touches crossmember,

    Finally fitted pushrods and got the motor finished

    Back seat fits onto original mounts so will work like itís supposed to

  5. #80
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default

    Didnt make madaz burnouts either obviously haha

  6. #81
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default


    Radiator in, fuel and wiring is about all thatís left


    Lower radiator hoses couldnít find any photos of other conversions so here are some for future references, standard lower cut to just a 90 degree, I think standard Ls1 commy was lying on the floor and fits perfect just need pipe to meet them together

  7. #82
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default


    I want this height all the time has pedders 2024 springs know but theyíre about 1-2 inches higher

  8. #83
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default


    Seat fits on original mounts

  9. #84
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default


    You Can imagine the words that I had to say when this happened, bolt was tight about half way down so I ran a thread chaser down until it snapped off, not on purpose, all fixed now only took about 20mins to get the box back far enough to get the converter out thank god for hoists and gearbox jacks
    Last edited by 10WHK; 15-12-2018 at 09:50 PM.

  10. #85
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default


    And the important Summernats apparel
    Last edited by 10WHK; 14-12-2018 at 10:44 PM.

  11. #86
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default

    Cutting it fine cars at panel beaters getting touched up, then to a mates for wiring, then up to upholsterer. All the boys lookin after me so hopefully We make it

  12. #87
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default




  13. #88
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default

    Original colour is darker then what the door cards are so Iíll have to get them recovered at a later date, seats look good canít wait till the interiors all in
    Last edited by 10WHK; 21-12-2018 at 10:42 PM.

  14. #89
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default


  15. #90
    casual poster
    Join Date
    Mar 2017
    Location
    Qld
    Posts
    134

    Default

    Wirings finished, back to get interior in.
    Little bits left, so close

Page 6 of 9 FirstFirst ... 3456789 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Those dam burnouts
    By TOAD4.2 in forum Members Lounge
    Replies: 5
    Last Post: 08-07-2013, 09:14 PM
  2. Burnouts are burnouts
    By Petrolhead in forum Members Lounge
    Replies: 39
    Last Post: 29-10-2011, 04:32 AM
  3. Replies: 10
    Last Post: 18-02-2010, 09:09 PM
  4. Us vs Them burnouts.
    By HQforme in forum Images & Videos
    Replies: 0
    Last Post: 09-02-2010, 09:08 PM
  5. Burnouts in an ej?
    By )( E D )( in forum Members Lounge
    Replies: 17
    Last Post: 29-01-2010, 10:24 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •